| Name |
Description |
|
Absorptivity
|
Gets or sets the Absorptivity.
|
|
AdditiveProcess
|
Gets or sets the AdditiveProcess.
|
|
ASCParallel
|
Gets or sets the ASCParallel.
|
|
ASCPerpendicular
|
Gets or sets the ASCPerpendicular.
|
|
ASCVertical
|
Gets or sets the ASCVertical.
|
|
BeamDiameter ***OBSOLETE*** Use of `double` for BeamDiameter is deprecated, use `Quantity` instead.
|
Gets or sets the beam diameter.
The type for the setter can be either double or Quantity.
Support for double is deprecated and will be removed in a future release.
The type returned by the getter is a Quantity.
An exception will be thrown for unsupported types.
An exception will be thrown if the value is less than or equal to 0 with inherent strain disabled.
An exception will be thrown if the value is less than 0.00002 or greater than 0.00014 meters when
inherent strain is enabled and the inherent strain definition is Thermal Strain.
|
|
BeamPower ***OBSOLETE*** Use of `double` for BeamPower is deprecated, use `Quantity` instead.
|
Gets or sets the beam power.
The type for the setter can be either double or Quantity.
Support for double is deprecated and will be removed in a future release.
The type returned by the getter is a Quantity.
An exception will be thrown for unsupported types.
An exception will be thrown if the value is less than or equal to 0 with inherent strain disabled.
An exception will be thrown if the value is less than 50 or greater than 700 watts when
inherent strain is enabled and the inherent strain definition is Thermal Strain.
|
|
BuildGasConvectionCoefficient
|
Gets or sets the BuildGasConvectionCoefficient.
|
|
BuildGasOrPowderTemperatureType
|
Gets or sets the BuildGasOrPowderTemperatureType.
|
|
BuildGasTemperature
|
Gets or sets the BuildGasTemperature.
|
|
BuildMachineType
|
Gets or sets the BuildMachineType.
|
|
BuildPowderConvectionCoefficient
|
Gets or sets the BuildPowderConvectionCoefficient.
|
|
BuildPowderTemperature
|
Gets or sets the BuildPowderTemperature.
|
|
BuildRadiationEmissivity
|
Gets or sets the radiation emissivity for the build phase. If the input value is outside the accepted range of 0–1,
an ArgumentOutOfRangeException is thrown. An InvalidOperationException is also thrown if BuildUseRadiationBC is set to false.
|
|
BuildRoomTemperature
|
Gets or sets the ambient gas temperature in the chamber during printing. Used as the ambient reference for convection and radiation on all active clusters and base surfaces during the build. Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than or equal to 0 °C.
|
|
BuildSequence
|
Gets the build sequence. An exception is thrown if the EnableBuildSequence property is False.
|
|
BuildUseRadiationBC
|
Gets or sets whether to use the radiation boundary condition during the build phase.
|
|
Comments
|
Gets the list of associated comments.
|
|
CooldownGasConvectionCoefficient
|
Gets or sets the CooldownGasConvectionCoefficient.
|
|
CooldownGasOrPowderTemperatureType
|
Gets or sets the CooldownGasOrPowderTemperatureType.
|
|
CooldownGasTemperature
|
Gets or sets the CooldownGasTemperature.
|
|
CooldownPowderConvectionCoefficient
|
Gets or sets the CooldownPowderConvectionCoefficient.
|
|
CooldownPowderTemperature
|
Gets or sets the CooldownPowderTemperature.
|
|
CooldownRadiationEmissivity
|
Gets or sets the radiation emissivity for the cool down phase. If the input value is outside the accepted range of 0–1,
an ArgumentOutOfRangeException is thrown. An InvalidOperationException is also thrown if CooldownUseRadiationBC is set to false.
|
|
CooldownRoomTemperature
|
Gets or sets the ambient gas temperature in the chamber during cooldown. Used as the ambient reference for convection and radiation on all active clusters and base surfaces during the build. An exception is thrown if the supplied value is less than or equal to 0 °C.
|
|
CooldownTime
|
Gets or sets the duration of the cooldown process. Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than 0.
|
|
CooldownUseRadiationBC
|
Gets or sets whether to use the radiation boundary condition during the cool down phase.
|
|
DataModelObjectCategory
|
Gets the name of the current DataModelObject's category.
|
|
DEDBuildGasConvectionCoefficientBase
|
Gets or sets the convection coefficient from base plate outer surfaces to chamber gas during printing. Controls how strongly the base plate acts as a heat sink. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition or if the supplied value is less than 0.
|
|
DEDBuildGasConvectionCoefficientPart
|
Gets or sets the convection coefficient from build surfaces to chamber gas during printing. Automatically applied to each activated cluster. Low values approximate adiabatic conditions; higher values increase cooling, especially important for bulky structures. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition or if the supplied value is less than 0.
|
|
DEDBuildRadiationEmissivityBase
|
Gets or sets the emissivity of base plate surfaces during build. Changes how strongly the base plate exchanges heat radiatively with the environment. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition. An exception is also thrown if the supplied value is less than 0, or greater than 1.
|
|
DEDBuildRadiationEmissivityPart
|
Gets or sets the emissivity of build surfaces during build. Higher values increase radiative heat loss from the printed part. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition. An exception is also thrown if the supplied value is less than 0, or greater than 1.
|
|
DEDClusterCoolingTimeRatio
|
Gets or sets the ratio defining the cooling portion of total cluster time. Lower values shorten cooling and lengthen effective heating, increasing temperature spikes. A value of 0.8 means ~20 % of cluster time is heating and ~80 % is cooling. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition. An exception is also thrown if the supplied value is less than or equal to 0, or greater than 1.
|
|
DEDCooldownGasConvectionCoefficientBase
|
Gets or sets the convection coefficient from base plate surfaces to chamber gas during cooldown. Governs how quickly the base plate returns to ambient conditions. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition or if the supplied value is less than 0.
|
|
DEDCooldownGasConvectionCoefficientPart
|
Gets or sets the convection coefficient from build surfaces to chamber gas during cooldown. Higher values increase cooling after deposition stops; very low values can nearly disable convection for sensitivity studies. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition or if the supplied value is less than 0.
|
|
DEDCooldownRadiationEmissivityBase
|
Gets or sets the emissivity of base plate surfaces during cooldown. Changes how strongly the base plate exchanges heat radiatively with the environment. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition. An exception is also thrown if the supplied value is less than 0, or greater than 1.
|
|
DEDCooldownRadiationEmissivityPart
|
Gets or sets the emissivity of build surfaces during cooldown. Higher values increase radiative heat loss from the printed part. An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition. An exception is also thrown if the supplied value is less than 0, or greater than 1.
|
|
DEDMaterialDepositionRate
|
Gets or sets the material feed rate in volume per time unit determined by layer thickness × weld width × deposition speed. Along with Cluster Volume, it defines cluster time (volume ÷ deposition rate). An exception is thrown if the AMProcessType property is not DirectedEnergyDeposition. An exception is also thrown if the supplied value is less than or equal to 0.
|
|
DepositionThickness
|
Gets or sets the DepositionThickness.
|
|
DwellTime
|
Gets or sets the DwellTime.
|
|
DwellTimeMultiple
|
Gets or sets the DwellTimeMultiple.
|
|
EnableBuildSequence
|
Gets or sets the EnableBuildSequence flag. This flag must be set to enable the Build Sequence Definition properties. [Default = False]
|
|
Figures
|
Gets the list of associated figures.
|
|
GeneratedLayerRotationAngle ***OBSOLETE*** Use of `double` for GeneratedLayerRotationAngle is deprecated, use `Quantity` instead.
|
Gets or sets the generated layer rotation angle.
The type for the setter can be either double or Quantity.
Support for double is deprecated and will be removed in a future release.
The type returned by the getter is a Quantity.
An exception will be thrown for unsupported types.
An exception will be thrown if the value is less than 0 or greater than 180 degrees.
|
|
GeneratedStartLayerAngle ***OBSOLETE*** Use of `double` for GeneratedStartLayerAngle is deprecated, use `Quantity` instead.
|
Gets or sets the generated start layer angle.
The type for the setter can be either double or Quantity.
Support for double is deprecated and will be removed in a future release.
The type returned by the getter is a Quantity.
An exception will be thrown for unsupported types.
An exception will be thrown if the value is less than 0 or greater than 180 degrees.
|
|
HatchSpacing
|
Gets or sets the HatchSpacing.
|
|
HeatingDuration
|
Gets or sets the HeatingDuration.
|
|
HeatingMethod
|
Gets or sets the HeatingMethod.
|
|
Images
|
Gets the list of associated images.
|
|
InherentStrain
|
Gets or sets the InherentStrain.
|
|
InherentStrainDefinition
|
Gets or sets the InherentStrainDefinition.
|
|
InternalObject
|
Gets the internal object. For advanced usage only.
|
|
InterpassCoolingConvergenceThreshold
|
Gets or sets the maximum allowed percent change in the layer’s maximum temperature between iterations. Cooling is considered converged when the change is less than or equal to this value. Default is 0.1 (10%). Available when the interpass cooling method is set to TemperatureBased. Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than 0, or greater than 1.
|
|
InterpassCoolingMaxIterationNumLayer
|
Gets or sets the upper limit on the number of cooling iterations per layer when using TemperatureBased interpass cooling method. Default is 5. Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than 1.
|
|
InterpassCoolingMethod
|
Gets or sets the method used to control dwell time between layers. Applicable only when AMProcessType property is DirectedEnergyDeposition.
|
|
InterpassCoolingTargetTemperature
|
Gets or sets the temperature that a layer must cool to before the next layer begins. Available when the interpass cooling method is set to TemperatureBased. Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than or equal to 0 °C.
|
|
InterpassCoolingTimeStepSize
|
Gets or sets the time increment between repeated thermal solves while cooling a layer in TemperatureBased interpass cooling method. Smaller values give finer control but require more solves. Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than or equal to 0.
|
|
LayerHeightType
|
LayerHeightType - Get/Sets the layer height type.
|
|
LayerHeightValue
|
Gets or sets the LayerHeightValue.
|
|
MachineLearningModel
|
Gets or sets the MachineLearningModel.
|
|
Name
|
Gets the name of the object.
|
|
NumberOfHeatSources
|
Gets or sets the NumberOfHeatSources.
|
|
ObjectId
|
Gets the internal id of the object.
|
|
ObjectTags
|
Gets an IEnumerable object of the tags that 'this' is a part of.
|
|
Parent
|
Gets the parent object.
|
|
PowderPropertyFactor
|
Gets or sets the PowderPropertyFactor.
|
|
PreheatDuringPrinting
|
Gets or set whether to apply a temperature boundary condition throughout the entire build. When set to False, the boundary condition is applied only in the first load step; When set to True, the boundary condition is maintained during all cluster activations. Default: False. Applicable only when AMProcessType property is DirectedEnergyDeposition.
|
|
PreheatGeometry
|
Gets or sets the preheat geometry scoping. Applicable only when AdditiveProcess is DirectedEnergyDeposition and PreheatDuringPrinting is On. Otherwise, an exception is thrown.
|
|
PreheatTemperature
|
Gets or sets the preheat temperature on the build plate. An exception is thrown if the supplied value is less than or equal to 0 °C.
When AdditiveProcess is PowderBedFusion, it sets the value of the starting temperature of the build plate.
When AdditiveProcess is DirectedEnergyDeposition and PreheatDuringPrinting is On, this temperature is prescribed on the scoped geometry as a boundary condition.
|
|
ProcessTemperature
|
Gets or sets the temperature of the feed material as it is exiting the nozzle—usually melting temperature or above. This value automatically defaults to the build material's melting temperature (or 1000 °C if the melting temperature is not defined). Applicable only when AMProcessType property is DirectedEnergyDeposition. An exception is thrown if the supplied value is less than or equal to 0 °C.
|
|
Properties
|
Gets the list of properties for this object.
|
|
RemovalStep
|
Gets or sets whether to perform base removal after cooldown. Default: False. Applicable only when the AMProcessType property is set to DirectedEnergyDeposition.
|
|
ScanPatternBuildFilePath
|
Gets or sets the ScanPatternBuildFilePath.
|
|
ScanPatternDefinition
|
Gets or sets the ScanPatternDefinition.
|
|
ScanSpeed
|
Gets or sets the ScanSpeed.
|
|
ScanStripeWidth ***OBSOLETE*** Use of `double` for ScanStripeWidth is deprecated, use `Quantity` instead.
|
Gets or sets the scan stripe width.
The type for the setter can be either double or Quantity.
Support for double is deprecated and will be removed in a future release.
The type returned by the getter is a Quantity.
An exception will be thrown for unsupported types.
An exception will be thrown if the value is less than 0 with inherent strain disabled.
An exception will be thrown if the value is less than 0.001 or greater than 0.1 meters
when inherent strain is enabled and the inherent strain definition is Thermal Strain.
|
|
StrainScalingFactor
|
Gets or sets the StrainScalingFactor.
|
|
StrainScalingFactorInterpolationMethod
|
|
|
StrainScalingFactorX
|
Gets or sets the StrainScalingFactorX.
|
|
StrainScalingFactorXInterpolationMethod
|
|
|
StrainScalingFactorY
|
Gets or sets the StrainScalingFactorY.
|
|
StrainScalingFactorYInterpolationMethod
|
|
|
StrainScalingFactorZ
|
Gets or sets the StrainScalingFactorZ.
|
|
StrainScalingFactorZInterpolationMethod
|
|
|
ThermalStrainMaterialModel ***OBSOLETE*** ThermalStrainMaterialModel is deprecated, please use MachineLearningModel instead.
|
Gets or sets the MachineLearningModel using the deprecated ThermalStrainMaterialModel methods.
|
|
ThermalStrainMethod
|
Gets or sets the ThermalStrainMethod.
|
|
ThermalStrainScalingFactor
|
Gets or sets the ThermalStrainScalingFactor.
|
|
VisibleProperties
|
Gets the list of properties that are visible for this object.
|